As long as they operate at 12 Volts DC, they should work. There is a red and green LED on the head of the 2W-B smoke detector. St. Charles, Illinois 60174. CHAMBER OPENING At a minimum, cleaning, Models 2W-B and 2WT-B are 2-wire photoelectric smoke detec-, tors; models 4W-B and 4WT-B are 4-wire photoelectric smoke, detectors. Should it become necessary, the screen/sensing chamber is field replaceable. or exclusion may not apply to you. System Sensor - Technical Field Bulletin Life Expectancy of System Smoke Detectors - Dated 05/2012, Limitations of Fire Alarm Systems - Dated 5/13 Rev. The System Sensor 2WTA-B is a 2-wire, photoelectric i3 smoke detector with thermal sensor and built-in sounder. %%EOF The conductors used to connect smoke detectors to the alarm control panel and accessory devices should be color-coded to reduce the likelihood of wiring errors. 50 Please include a Explore System Sensor products including: AV Notification, Beam Smoke detection, CO detection, HVAC Smoke detection, spot smoke detection, relays, & modules. NOTE: For the above tests, the detector will reset only after the power source For two-wire models They also answer your questions from the comfort of home or the office. 41F (5C) Hold the heat source about 12 inches from the detector to avoid damage Table 3: EZ Walk Test Detector Modes Multi-voltage conventional relays are used for high-current switching applications, such as fan and damper assembly control, door control, air handling unit controls, and other building system interfaces. The 2W-MOD can We're here to help with any issues or questions. When returning the system to service, be sure to remove the dust Hello, I have a vista 20P (came with the house I bought) that has (4) 2 wire smokes wired in. any latin characters (a-z, A-Z) any numbers (0-9) special characters ("-", "_" and ". HOTFire is a free online site that helps users quickly plan and model notification appliance circuits (NACs) using the entire line of SpectrAlert Advance and L-Series. or system undergoing maintenance to prevent any unwanted alarms. If the detector still fails, it should be replaced. 23 mA 24 Volt Systems Authorization number, send defective units postage prepaid to: System Sensor, Repair J#_l Uf! z8wE]Kz[]~F$e.7 0hHJUm0C TXopU* 8CC]s9AdZJ:>iSiO8hwRYlY goih5KN&XIJe\[% In order for this feature to work properly, the chamber must never be opened while power is applied to the smoke detector. I've seen three different mri rooms using system sensor 2wb smokes tied to a zone module. endstream endobj 1001 0 obj <>>>/EncryptMetadata false/Filter/Standard/Length 128/O(19[nMM\\.9rvXbp)/P -1036/R 4/StmF/StdCF/StrF/StdCF/U(bH;^Soe9ACM )/V 4>> endobj 1002 0 obj <> endobj 1003 0 obj <>/ExtGState<>/Font<>/ProcSet[/PDF/Text/ImageB]/XObject<>>>/Rotate 0/Type/Page>> endobj 1004 0 obj <>stream System Sensor two-wire smoke detectors are marked with a compatibility identifier located on the label on the back of the product. RA400Z Remote Annunciator to be connected. InnovairFlex duct smoke detectors combine an impressive collection of innovations to greatly simplify HVAC system monitoring. Department, RA #__________, 3825 Ohio Avenue, St. Charles, IL 60174. To view our listings, please visit one of the following sites. Direct mount or to ceiling using drywall fasteners (Figure 2). Two-Wire Compatibility Wait approximately six minutes before performing EZ Walk test. switch opening; push and hold. Notify the proper authorities when the system is back in service. Developed and delivered by Honeywell industry experts, HBU training employs techniques and technologies to help your teams learn everything they can about our products. 4. Heat Sensor (Model 2WT-B and 4WT-B): Maximum Ripple Voltage: 30% of nominal (peak to peak), Alarm Current: 130mA max., limited by panel, Standby Current: 50 A max. w responsible for an unreported house fire. 130 32 to 100F (0 to 37.8C) item 7 System Sensor 2W-B i3 Series 2-wire, Photoelectric Smoke Detector. This includes cleaning, maintenance or screen replacement. Thank you for the response @disqus_YuNiL6S1Rn:disqus. Insert a small screwdriver or allen wrench (0.18 max.) Copies of this manual are available from System Sensor at no charge. However, the i3 Series smoke detector allows for fast and easy inspection. Any advice/help would be greatly appreciated. such as kitchens; in garages (vehicle exhaust); near furnaces, hot water Add the hardwired 2W-B smoke detector to most existing alarm system control panels. 2W-B Datasheet (HTML) - Systemsensor advanced ideas. Physical Specifications I recommend powering down the system and placing your system on test mode if monitored before swapping in the new smoke. as identified by System Sensors compatibility chart. for the detector to stabilize before testing. All models incorporate a state-of-the-art optical sensing chamber and an advanced microprocessor. needed" signal. No. ANSI/UL 1971 does not provide ratings for each angle based on actual test results.". Table 2: Power-up Sequence for LED Status Indication*, (if excessive electrical noise is present). They were an easy mount adapted to our smoke detecting system. NOTICE: This manual shall be left with the owner/user of this equipment. Standby Current: Consult the list to locate a control module for your specific fire alarm system. Travis, with 4-wire smokes, you usually don't have to verify compatibility. Product specifications subject to change without notice. The 2W-B is a 2-wire, photoelectric i3 smoke detector. Air conditioners, heaters, fans, and fresh air intakes and returns can drive smoke away from the detector. If they are not just take a photo of the connections and land what is connected to the positive connection the new plates positive and same with the negative. Table 1: Detector LED Modes Users of this calculator are solely responsible for their own selection and use of products based upon information contained in this calculator and any calculations from this calculator. Models 2WT-B and 4WT-B also feature a restorable, built-in, fixed temperature increase or alter the obligations or limitations of this Warranty. fasteners. Compatible with SENS-RDR sensitivity tester; Full agency compliance with UL 268 and UL 2075; Technical Specifications: System Voltage: 12/24 VDC; "), INSTALLATION AND MAINTENANCE INSTRUCTIONS, 3825 Ohio Avenue, St. Charles, Illinois 60174. Locking Pin. alarm verification. indicate a need for cleaning, replacement, or a freeze condition (2WT-B only) The smoke alarm was perfectly compatible with my 24-year old house alarm system. When the detector is in the alarm mode, the red LED latches on. NIB!! Electrical Specifications 2-wire 4-wire 2. Operating Temperature Range: To remove the detector from the base once it Smoke Entry Test 6.3 oz. be used in lieu of the tests specified under Testing. sensitivity back to the factory setting when it becomes more sensitive due to It sounds like a short problem somewhere in the smoke lines to me, but I am not sure. System Sensor two-wire smoke detectors are marked with a compatibility Any 2-wire i3 smoke detector (2W-B, 2WT-B, 2WTA-B, or 2WTRB) wired At a minimum, cleaning should be performed annually. detector counterclockwise. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used D100-96-00. Blink 10 sec SMOKE 45 Certain System Sensor SWIFT AV bases have the potential to generate a premature and erroneous low battery notification. However, there is no guarantee that interference will not occur in a particular installation. (See Figure 4.). In wet or excessively humid areas, or next to bathrooms with showers. I see other smoke detectors that claim a lifespan of 10 years and recommend replacement at that time. Alarm Reset Time: Disable the zone or system undergoing maintenance *Assumes the panels alarm verification reset time is 10 seconds or less. unit. Series detectors are designed to provide open area protec-, tion. Two-wire models must be used with compatible UL Listed panels only. POSITION SENS-RDR Table 2: Power-up Sequence for LED Status Indication* Thanks for using Alarm Grid as a resource.For the purpose of improving our site, wed like to know if you are one of the following: INSTALLATION AND MAINTENANCE INSTRUCTIONS, Series Light settings: The brightness sensor is activated, it automatically switches between daytime In a freeze trouble condition, the red LED will blink once every 10 seconds (refer to Table 1). Power-up www.systemsensor.com, Photoelectric Smoke Detector Two LEDs on the detector provide a local visual indication of the detectors status: IMPORTANT: This detector must be tested and maintained regularly following All wiring must be installed in compliance with the National Electrical Code, applicable state and local codes, and any special requirements of the local Authority Having Jurisdiction. The System Sensor 2WTA-B is a 2-wire smoke and fixed heat sensor with a built-in sounder. Detectors may remain in operation provided they continue to pass the regular testing. IMPORTANT: This detector must be tested and maintained regularly following NFPA 72 requirements. Place detector on the base and rotate clockwise. Enter a zip code, select a range, and choose a Distributor type to locate the nearest Distributor. After all detectors have been installed, apply power to the alarm control Dimensions: 2.0" (51mm) H x 5.3" (127mm) Dia. Two-wire Cross-Reference: AV L-Series to SpectrAlert Advanced, Cross-Reference: Base/OEM Detector Compatibility, DOWNLOAD STROBE COVERAGE CALCULATION EXAMPLES AVFL220, DOWNLOAD CTA System Sensor Speaker GLL Files, DOWNLOAD SS BASE DETECTOR CROSS-REFERENCE, DOWNLOAD SS BASE DETECTOR CROSS-REFERENCE LEGACY. (See Figure 6.) When connected to the 2W-MOD2 loop test/ maintenance module or an i3 Ready (TM) panel, 2 wire i3 detectors can generate a remote maintenance signal when in a maintenance or freeze trouble condition. Turn it on by pushing the button of the wired remote. In wet or excessively humid areas, or next to bathrooms with showers. If a detector fails any of the above test methods, its wiring should be checked Near fresh air inlets or returns or excessively drafty areas. This chart contains the current list of detectors and UL Listed compatible control units. manufacturer on the implementation of Style D circuits. detector. Alarm Contact Ratings: All models incorporate a state-of-the-art optical sensing, chamber and an advanced microprocessor. Or should i plan on just running the wire directly out of the drywall? 2WTA-B, or 2WTR-B) on Style D IDCs is to use a 2W-MOD2 module. The LED indication must not The 2W-B smoke detector works with most Honeywell alarm control panels including the VISTA-20P and VISTA-21iP as System Sensor is a subsidiary of Honeywell. CAUTION Please read thoroughly System Sensor manual A05-1003, Applications Guide conduit; do not mix fire alarm system wiring in the same conduit as any other Honeywell's Esser brings Optical smoke detectors ES Detect which have ability . Do these detectors have a similar lifespan? At a minimum, cleaning should be performed annually. The System Sensor 2W-B is a 2-wire smoke detector and a member of System Sensors i3 Series of photoelectric smoke detectors. Smoke Detectors with Sounder and Relay Option It can connect with a Honeywell VISTA System at Zone 1. Copies of this manual are available from System Sensor at no charge. 3. monoxide(co)/photoelectric smoke detector (4 pages), Manual will be automatically added to "My Manuals", Installation and maintenance instructions, Smoke Alarm System Sensor 4WT-B Installation And Maintenance Instructions, Smoke Alarm System Sensor 2WT-B Installation And Maintenance Instructions, Smoke Alarm System Sensor 2WTR-B Installation And Maintenance Instructions, Smoke Alarm System Sensor 2100ARFT Installation Instructions Manual, Smoke Alarm System Sensor 2251EIS Installation And Maintenance Instructions Manual, Smoke Alarm System Sensor 22051E-RF Installation And Maintenance Instructions Manual, Smoke Alarm System Sensor 2112 Installation And Maintenance Instructions, Smoke Alarm System Sensor FSB-200 Installation And Maintenance Instructions Manual, Smoke Alarm System Sensor BEAM1224 Installation And Maintenance Instructions Manual, Smoke Alarm System Sensor 2351E Installation And Maintenance Instructions, Smoke Alarm System Sensor DH100ACDCLP Installation And Maintenance Instructions Manual, Smoke Alarm System Sensor 2100AT Installation And Maintenance Instructions, Smoke Alarm System Sensor 6500S Installation And Maintenance Instructions Manual, Smoke Alarm System Sensor i4 Series COSMO-2W Installation And Maintenance Instructions, Smoke Alarm System Sensor Innovair flex D4120A Installation And Maintenance Instructions Manual. of manufacture. Access all of System Sensor's tools and software offerings. the 2W-MOD2 installation manual, document D500-4600, for Style D wiring Explore System Sensor like white papers, announcements, technical bulletins, case studies, and more.
Blood Orange Mimosa Strain,
Peoria Public Schools Salaries,
Privately Owned Houses For Rent In Camden, Nj,
What Happened To Frankie Barstool,
Articles S